 |
 |
 |
|
ClimoPlate ™ is a New Zealand manufactured Alkyd / Bitumen co-polymer, solvent / water emulsion based paint developed primarily for New Zealand outdoor conditions.
ClimoPlate ™ is specifically but not exclusively formulated to act as a top coat over bitumen based sealers such as our GilsoFlex™ and FlexsoTar™ products. It is ideally suited for painting of exposed metal roofs, cement tile roofs and steel structures. It is compatible and suitable to be used on Decramastic and Butynol roofs.
ClimoPlate ™ can also be used on other substrates like timber etc.
Because of its disinfecting effect, it will retard the growth of moss or lichen.
Substrate surface preparation requirements are minimal.
Roof requires one coat only and 10 Litres will cover approximately 18 to 36 Square Meters, depending on roof surface thus one (1) Litre will cover approximately 4,5 to 9 Square Meters.
ClimoPlate ™ is intended primarily for surface application by brushing, rolling or airless spraying.
A re-coat might be required after 8 to 10 years.
We are in the process of adding more colours to our range. (Please ask via "eMail" if you would like us to match a specific colour for you, and we will advise)
- For more detailed information please see our documents in the "Extended Information" tab
Packaging: Available in 4 litre, 10 litre and 20 litre tins
For Use On: Suitable for use on any cement tile and corrugated steel roofs, Decramastic roofs, Butynol roofs, steel structures, timber, concrete brick and block work etc.
Surface Preparation: Ensure surface is dry, dust free and not contaminated (Remove Contamination, moss, mould and any old, loose and flaky paint and rust before coating)
Colour: Please see our web-site as we are in the process of adding more colours to our range
Before Applying: The paint should be thoroughly stirred for at least 5 mins.
Application: Brush, Roller, Spray (we supply a suitable spray thinner if required)
Coverage: Depends upon surface:
– Tile roofs typically 3 - 6 m2/litre.
– Corrugated metal roofs typically 4 - 8 m2/litre.
No of Coats: Generally only one coat required, a second coat can be applied dependent on the condition of the roof.
Recoat Time: As soon as previous coat is touch dry (approximately 6 hours), an additional coat can be applied if required.
Drying Time: Generally allow 24 hours, depending on surface and ambient conditions for the paint to be touch dry.
Thinners: Not recommended, however for spraying please see our web-site for a suitable thinner.
Clean Up: Clean equipment using recommended thinner, kerosine or mineral turpentine
Durability: Recoat after 8 summers if required. In harsh climatic areas a recoat might be required sooner.
Other:
– Contains volatile solvent, keep away from heat and open flame.
– Keep out of reach of children.
– Keep closed when not in use, avoid breathing vapour - ensure good air flow when applying.
– Stir very regularly during application to ensure consistency of product.
– Do not apply if surface temperature is below 5°C or above 40°C
Storage, Handling Safety: Refer to attached Material Safety Data Sheet (MSDS ClimoPlate) also refer to attached “Health and Safety in the Surface Coating Industry” Brief 3, October 2007 as published by the Department of Labour.
|
|
|
 |
|
 |
|
|
|
 |
|
 |
|
Features
- ClimoPlate ™ is a Bitumen/Alkyd Top Coat paint suitable over bitumen based sealers and coatings.
- ClimoPlate ™ is a flexible coating and will not break down due to distortion and movement, caused by weather exposure
ClimoPlate ™ is non-corrosive to metals and can be painted directly over bitumen based products, bare steel, galvanised, powder coated, minor surface rust or previously painted steel and concrete with minimum surface preparation requirements.
ClimoPlate ™ is suitable on metal and concrete tile roofs. It can also be used on concrete brick and block work, plywood and timber.
- Can be used on other structures to paint the surface
- Drinking water collected from roofs coated with ClimoPlate ™ is safe to consume
|
|
|
|
|
|
|
